Pendleton Cafe Shutters From Pendleton Window Treatments

Full-height blinds would waste a tall window

Existing panels stop at a random height

The sill is too deep for panels to swing

An older house needs a period-correct detail

There isn't enough depth for a full shutter frame

A tub sits under a window with no privacy

A deep sill holds plants you want visible

The faucet blocks anything that opens into the room

Blinds cover glass you would rather leave open

Neighbors can see in at sitting height

The divide height decided at the window with you standing in the room and then sitting in it

Three widths and three heights taken across the lower part of the opening, plus a diagonal check for square

The horizontal bar across the middle of the opening located, since that's usually where the panels should stop

One divide height carried across every window in the room instead of being set opening by opening

The sightline from the sidewalk checked, because privacy at sitting height is the whole point of the product

Mounting depth read at the lower corners so panels clear handles, cranks and anything else inside the opening

Frame style chosen per opening: an L-frame inside, a Z-frame lapping the casing, or a hanging strip on the face

Whether the top of the panel gets a capping frame or is left open decided at the measure, since that edge is visible

Material specified per room, poly or composite where humidity swings and hardwood where the room stays conditioned

Louver size chosen against a short panel, where a large louver reads out of scale faster than it does full height

Panel count and swing direction drawn so nothing hits a faucet, a countertop or a window crank

A T-post drawn on wide openings so each panel stays a width that swings properly and stays flat

Divider rails left out unless the panel is unusually tall, since a cafe panel rarely needs one

Hinge style and finish chosen knowing the hardware sits at eye level for anyone sitting down

Paint or stain matched to the existing trim with a physical sample in the room, never off a screen

Whatever goes above the panels planned in the same visit, or the upper glass deliberately left bare

Written contract with scope, dates and total price, as IC 24-5-11 requires on residential work over $150

Frames shimmed plumb, louver tension set panel by panel, then caulk and touch-up run at the frame line

Poly and composite panels: An engineered core with a hard painted finish that ignores moisture. This is what goes over a kitchen sink and in a bathroom, because Indiana humidity moves hardwood and a moved panel stops closing against its neighbor.

Hardwood panels: Usually basswood, lighter for the same panel and able to carry a stain that shows grain. On a short cafe panel in a conditioned front room, stained hardwood against original trim is a look no painted composite gets close to.

2 1/2 inch louver: The right default on a half-height panel. A short panel only holds so many louvers, and going small keeps the proportion sane and gives you finer control over the angle you tilt them to.

3 1/2 inch louver: Worth using where the lower part of the window is unusually tall, or where full-height shutters elsewhere in the house already use this size and you want the rooms to agree with each other.

L-frame: A simple right angle sitting inside the opening, lapping the face of the trim slightly. It's the cleanest install when the opening has depth, and on a cafe it keeps the frame from drawing attention to the fact that it stops halfway up.

Z-frame: Adds a flange that covers the edge of the existing casing, which hides an opening that has settled and gives the installer somewhere to take up the difference. It's the usual answer in an older house, where nothing is quite plumb.

Hanging strip on the face: Hinges mount to a narrow strip fastened onto the face of the casing rather than a full frame. It's the lightest-looking option, it works where the opening has almost no depth, and it puts the panels proud of the trim.

Hidden tilt rod: The linkage moves into the stile so the louver face is uninterrupted. On a cafe panel that sits right at eye level for anyone at a table, losing the center rod makes a noticeable difference to how the window reads.

T-post on a wide opening: A fixed vertical post between panels so no single panel gets wide enough to sag or swing badly. It also gives the louvers something to close against in the middle, which is where a wide cafe otherwise leaks light and sightlines.

A shade above the panels: A roller, a Roman or a woven natural mounted above the cafe shutters covers the upper glass when you want it covered. This is how you keep the daylight most days and still kill a low sun that comes straight down the street.